Seaward PrimeTest 200 Betriebsanleitung Seite 1

Operating InstructionsPrimetest 200PrimeTest 200Operating InstructionsBracken Hill, South West Industrial Estate,Peterlee, Co. Durham SR8 2SW. England

PrimeTest 200Operating Instructions

Operating Instructions PrimeTest 200A multifunction testing instrument: used to perform comprehensive electricalsafety tests on:- Class I appliances-

2.0 Safety NotesThis PrimeTest 200 has been built and tested in accordance with:DIN VDE 0404 part 1 and 2.BS EN 61010 part 1.BS EN 61557 part 1, 2, 4

It should be noted that the following parts of the PrimeTest 200 are userserviceable and must be replaced with appropriate parts as detailed below:- 1

5.0 General Information5.1 The polarity indicator 1 is automatic. Only one polarity is indicated withrespect to the negative black socket 12 5.2 Th

7.0 Electrical SpecificationAppendix 1 specifies the operating error for all tests and functions of thePrimeTest 200.7.1 Earth continuity measuring ra

PrimeTest 200Operating Instructions67.4 Voltage measuring rangeMeasuring Range Resolution Accuracy Overload Protection250 V AC/DC 1V ±2% +2 digits 300

7.9 RCD testTest current 30mA r.m.sTest current accuracy +5%, - 0%Test duration 500ms maximum if RCD does not tripTrip time accuracy ±10%An input volt

PrimeTest 200Operating Instructions88.2 Differential Leakage Current,See figure 4.Attention - The Red or Black 4mm test sockets must not be usedwhilst

Attention - the differential leakage current measurement can beaffected by exposure of the PrimeTest 200 to magnetic fields orcurrent being absorbed b

Operating InstructionsPrimetest 200Operating InstructionsPrimetest 200Operating InstructionsPrimetest 200Fig 1.Fig 2.Fig 3.Fig 4.

108.4 IEC Lead TEST, IECSee Figure 6.8.4.1 Select the IEC test function on the rotary switch 10 .Do not connect the IEC lead to the PrimeTest 200, in

PrimeTest 200118.5.2 Plug the equipment under test (EUT) into the EUT socket 11 on the front of the PrimeTest 200.8.5.3 Plug the black insulation te

If the power test is selected but the mains supply has not been connected to the PrimeTest 200 then PE and PN symbols will flash and the test is inhib

8.7.7 If an external voltage of 30 V AC/DC or greater is present at the tips of the test probes a repetitive audible alarm sounds along with the flash

148.9 Temperature Measurement Function, °C.See Figure 11Attention - Disconnect the IEC mains cable from the IEC socketbefore commencing this test. Ele

9.1 Preparing to work on the PrimeTest 200.Make the PrimeTest 200 voltage free as follows, before opening the instrument.9.1.1 Disconnect the two test

9.4.8 Insert a new set of batteries into the battery compartment ensuring thatthe battery polarity matches the marking on the inside of the battery co

9.7.7 Lift one end of the defective fuse out of the fuse holder with the help ofa flat bladed screwdriver.9.7.8 Lift the defective fuse completely out

Appendix 1Class 1 Earth BondIntrinsic Error or Reference Conditions or Code Max ErrorInfluence Quantity Rated Operating Conditions SeenIntrinsic Error

IEC InsulationIntrinsic Error or Reference Conditions or Code Max ErrorInfluence Quantity Rated Operating Conditions SeenIntrinsic Error Reference Con

Operating InstructionsPrimeTest 200Fig 5.Fig 6.

Point to Point InsulationIntrinsic Error or Reference Conditions or Code Max ErrorInfluence Quantity Rated Operating Conditions SeenIntrinsic Error Re

VoltageIntrinsic Error or Reference Conditions or Code Max ErrorInfluence Quantity Rated Operating Conditions SeenIntrinsic Error Reference Condions A

Appendix 2PrimeTest 200 Diagnostic IndicationsMains Supply IconsPE PN NEThe mains supply is too high, too low or not present.Flash Flash OffThese icon

PrimeTest 200Operating Instructions

PrimeTest 200Operating Instructions

Operating InstructionsPrimeTest 200Fig 7.Fig 8.

Operating InstructionsPrimeTest 200Fig 9.Fig 10.

Operating InstructionsPrimeTest 200Fig 11

Operating InstructionsPrimeTest 200Fig 12B.Fig 12A.

PrimeTest 200Operating Instructions

Limited Warranty & Limitation of LiabilitySEAWARD Electronic Limited guarantees this product for a period of 1 year.The period of warranty will be